DG2747DN-T1-E4
| Parameters | |
|---|---|
| Switch Time (Ton, Toff) (Max) | 25ns, 25ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω (Max) |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.6V~4.3V |
| Normal Position | NO |
| Height | 550μm |
| Length | 1.4mm |
| Width | 1.4mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 600mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 190mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2747 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 190mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 25 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| -3db Bandwidth | 93MHz |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 52 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 75pF 55pF |
| On-state Resistance Match-Nom | 0.03Ohm |
| Switch Circuit | SPST - NO |
DG2747DN-T1-E4 Overview
Presented in 8-UFQFN, this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 8 terminations. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 8 pins. These analog multiplexers are built based on SPST - NO switching circuits. Use DG2747 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 600mOhm. For functions related to 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 4.3V volts for the multiplexer. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.6V. This multiplexer would work with 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 1.6V~4.3V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. It is possible to operate 2 inputs.
DG2747DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 93MHz
DG2747DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2747DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- CSU
- MP3 players
- SONET
- Cross Connects
- Central office
- Frame Relay Equipment
- 65 V DACs
- Fiber In The Loop (FITL)
- Ultrasound
- Channelized and Unchannelized DS3 applications
