DG2750DN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 1Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.7V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2750 |
| Output | SEPARATE OUTPUT |
| Pin Count | 10 |
| Power Supplies | 1.8/4V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 2μA |
| Max Supply Current | 2μA |
| Turn On Delay Time | 2.1 μs |
| Supply Type | Single |
| Turn-Off Delay Time | 130 ns |
| -3db Bandwidth | 49MHz |
| On-State Resistance (Max) | 1Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 50nA Typ |
| Channel Capacitance (CS(off), CD(off)) | 36pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 2.1μs, 130ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -60dB @ 300kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1700ns |
| Switch-off Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Height Seated (Max) | 0.6mm |
| Length | 1.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG2750DN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-UFQFN. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. A total of 10 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 2.7V is used, the electronic component should be turned on and run. There is an electrical component included in the 10 series. SPDT switching circuits are used in these analog switch ics. A total of 2 circuits make up this switch device. Search with DG2750 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 1Ohm. The functions of 10 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analog switch ics with Single supply type are cost-effective. It is recommended to use 1.8V as the lowest voltage for the electrical part. This digital switch can be operated with a current of 2μA. This analog switch requires a voltage of 1.8V~5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 2μA. There are SEPARATE OUTPUT outputs on this analog switch ic.
DG2750DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
2μA Supply Current
-3db Bandwidth: 49MHz
DG2750DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2750DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- High speed data transmission line cards
- Cellular phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ISDN NT1/TA
- CSU
- Audio and video routing
- Modems
- Communication systems
