banner_page

DG2753DN-T1-E4

60ns, 30ns SPDT 1.2Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG2753 16 Pins 2nA 2.7V 16-VFQFN Exposed Pad


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2753DN-T1-E4
  • Package: 16-VFQFN Exposed Pad
  • Datasheet: PDF
  • Stock: 558
  • Description: 60ns, 30ns SPDT 1.2Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG2753 16 Pins 2nA 2.7V 16-VFQFN Exposed Pad(Kg)

Details

Tags

Parameters
Channel-to-Channel Matching (ΔRon) 600m Ω (Max)
Crosstalk -90dB @ 10MHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.3V
Height 900μm
Length 3mm
Width 3mm
RoHS Status ROHS3 Compliant
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 16-VFQFN Exposed Pad
Number of Pins 16
Weight 57.09594mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
Resistance 600mOhm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Max Power Dissipation 1.385W
Technology CMOS
Terminal Position QUAD
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Number of Functions 3
Supply Voltage 2.7V
Terminal Pitch 0.5mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number DG2753
Output SEPARATE OUTPUT
Pin Count 16
Qualification Status Not Qualified
Number of Channels 1
Number of Circuits 3
Max Supply Voltage 4.3V
Min Supply Voltage 1.65V
Operating Supply Current 1μA
Max Supply Current 1μA
Turn On Delay Time 60 ns
Supply Type Single
Turn-Off Delay Time 30 ns
On-State Resistance (Max) 1.2Ohm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 90 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 35pF
On-state Resistance Match-Nom 0.4Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 60ns, 30ns
Charge Injection -25pC

DG2753DN-T1-E4 Overview


Due to its 16-VFQFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. Total terminations are 16. A 1 channel electronic part produces high-quality output. An 2.7V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. The analog switch ics are built using SPDT switching circuits. There are 3 circuits in this multiplexer. Try searching for the analog switch ic with DG2753 if you are looking for variants. A 600mOhm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 4.3V. The digital multiplexer has a low cost Single supply. The lowest voltage fed to the electronic component should be 1.65V. This digital switch can be operated with a current of 1μA. The voltage required by this switch device is 1.65V~4.3V, draining from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.

DG2753DN-T1-E4 Features


1 Channels
Switch Circuit: SPDT
1μA Supply Current

DG2753DN-T1-E4 Applications


There are a lot of Vishay Siliconix DG2753DN-T1-E4 Analog Switches & Multiplexers ICs applications.

  • Switching Systems
  • PBXs
  • Automatic test equipment
  • Intelligent PBX
  • Channelized and Unchannelized DS3 applications
  • Audio and video switching
  • Cable PC
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Communication systems
  • Remote wireless modules

Write a review

Note: HTML is not translated!
    Bad           Good