DG2789DN-T1-E4
| Parameters | |
|---|---|
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 72ns, 43ns |
| Charge Injection | 87pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 750μm |
| Length | 2.6mm |
| Width | 1.8mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2789 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 525mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 72 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 43 ns |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 49 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 81pF |
DG2789DN-T1-E4 Overview
Shipping overseas is convenient with the electronic component packed in 16-WFQFN. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. Due to its 1 channels, the electrical component produces high-quality output. A 3V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 16 pins. Unlike digital switches, these are based on SPDT switching circuits. Use DG2789 to search for variants of the digital switches. As far as internal resistance is concerned, it has 500mOhm. To find out what the functions of 16 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 4.3V. Single supply type digital switch with a low cost. 1.65V should be the lowest voltage fed to the electronic component. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 1.65V~4.3V to drain from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. Operating 4 inputs is required. This digital multiplexer has 8 outputs.
DG2789DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2789DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2789DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DVD-R
- Industrial
- Low-Voltage
- 65 V DACs
- Communication systems
- Multi-Line E1 Interface Cards
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cellular phones
- Transmit
