DG2799DN-T1-E4
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2799 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 1.385W |
| Max Supply Current | 1μA |
| Turn On Delay Time | 57 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 450mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 102pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 57ns, 45ns |
| Charge Injection | 160pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 900μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 430mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.385W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
DG2799DN-T1-E4 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WFQFN. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. 16 terminations have been made so far. The electronic part delivers high-quality output through its 2 channels. If the voltage supply is 3V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. A DPDT switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with DG2799 if you are looking for variants. A 430mOhm internal resistance characterizes this multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 4.3V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. 1.65V should be the lowest voltage fed to the electronic component. It would be sufficient to run this analogue multiplexer with 1μA current. An analogue multiplexer drains from a single voltage supply at 1.65V~4.3V. A digital multiplexer may suffer damage if voltage is applied above 1μA. Operating 4 inputs is required. This digital multiplexer has 8 outputs.
DG2799DN-T1-E4 Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
DG2799DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2799DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Medical Instrumentation
- Battery Powered Systems
- Central office
- Industrial and process control systems
- Video switching
- Modems
- Data switching
- Cross Connects
- Audio and video switching
