DG3000DB-T1-E1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-WFBGA |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 2.3Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG3000 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 100nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 76 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 33 ns |
| On-State Resistance (Max) | 2.3Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 61 dB |
| Current - Leakage (IS(off)) (Max) | 1.2nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 36ns, 22ns |
| Charge Injection | 38pC |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 79ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| RoHS Status | ROHS3 Compliant |
DG3000DB-T1-E1 Overview
Due to its 6-WFBGA packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. In total, there have been 6 terminations. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 2V, it should be turned on and run. It is part of the design of the 6 series that this electronic component is included. These analog multiplexers are built based on SPDT switching circuits. Using the DG3000 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 2.3Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 1.8V. For this multiplexer to operate, 100nA current would be sufficient. This analog switch requires a voltage of 1.8V~5.5V to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The 1 inputs need to be operated in order to work. This digital multiplexer has 2 outputs.
DG3000DB-T1-E1 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
DG3000DB-T1-E1 Applications
There are a lot of Vishay Siliconix DG3000DB-T1-E1 Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Battery-powered systems
- ISDN NT1/TA
- Relay Replacement
- Access Concentrators
- Cellular phones
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Channelized and Unchannelized DS3 applications
- HDTV
- T1/E1 Terminals
