DG300ABWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG300A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG300ABWE+ Overview
Packed in 16-SOIC (0.295, 7.50mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. An extended operating temperature of -25°C~85°C TA degrees Celsius. There are 16 terminations totally. A 1 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. The circuits in this analogue multiplexer number 2. Try searching for the analog switch ic with DG300A if you are looking for variants. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. To find out what the 16 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 25V. Dual, Single supply type digital switch with a low cost. 10V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 230μA current would be sufficient. The analogue multiplexer may be damaged if voltage is greater than 500μA. There is no problem with using dual supply voltage, but it should not exceed 18V. The voltage should be at least 5V if you are using dual power supplies. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electrical part can be operated at 18V voltage levels.
DG300ABWE+ Features
1 Channels
Switch Circuit: SPST - NO
230μA Supply Current
DG300ABWE+ Applications
There are a lot of Maxim Integrated DG300ABWE+ Analog Switches & Multiplexers ICs applications.
- Video switching
- ISDN NT1/TA
- Isolation
- MP3 players
- USB 1.1 signal switching circuits
- Avionics and Military Systems
- Sample-and-hold systems
- Intelligent PBX
- Cross Connects
- DSUs
