DG300ACJ+
| Parameters | |
|---|---|
| Min Supply Voltage | 5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG300A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
DG300ACJ+ Overview
The electronic component is convenient to ship overseas because it is packed in a 14-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. Totally, there are 14 terminations. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 14 pins are injected into the body of the electronic part. Circuits based on SPST - NO switching are used to construct these analog switch ics. There are 2 circuits in this switch device. Look for analog switch ic variants by searching with DG300A. As far as internal resistance is concerned, it has 50Ohm. For functions related to 14 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 18V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 5V. For this digital switch to work, 230μA current would suffice. When the digital multiplexer is charged above 500μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 18V. If you are using a dual power supply, you should attach at least 5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
DG300ACJ+ Features
1 Channels
Switch Circuit: SPST - NO
230μA Supply Current
DG300ACJ+ Applications
There are a lot of Maxim Integrated DG300ACJ+ Analog Switches & Multiplexers ICs applications.
- Audio and video signal routing
- Relay Replacement
- Microprocessor Controlled Analog Systems
- Communication systems
- FTTH
- High speed data transmission line cards
- Avionics test equipment
- Private Branch Exchange (PBX)
- New designs requiring multiplexer functions
- Cell phones
