DG300BDJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Power Dissipation | 470mW |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 2 |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 130ns (Typ) |
| Charge Injection | 8pC |
| Crosstalk | -74dB @ 500kHz |
| Drain to Source Resistance | 50Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG300BDJ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. It is part of the design of the 14 series that this electronic component is included. Unlike digital switches, these are based on SPST - NO switching circuits. A 50Ohm internal resistance characterizes this multiplexer. For details about the functions of 14 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analog switch ics with Dual, Single supply type are cost-effective. A low voltage of 13V should be applied to the electronic component. If you put voltage higher than 1mA on the digital multiplexer, damage may occur. Despite this switch's dual supply capability, its voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. 15V operating voltages are supported by the electronic component. The electrical component supports 2 inputs. It has a Drain to Source resistance of 50Ohm ohms.
DG300BDJ Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 50Ohm
DG300BDJ Applications
There are a lot of Vishay Siliconix DG300BDJ Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Sample hold systems
- Audio signal routing
- High reliability control systems
- Avionics test equipment
- Central office
- DSLAMs
- Optical Applications
- Remote Powered Equipment
- Channelized and Unchannelized DS3 applications
