DG301AAK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Screening Level | MIL-STD-883 Class B |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 5.08mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG301AAK/883B Overview
Due to its 14-CDIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 2:1. Operational temperature extended around -55°C~125°C TA. In total, there are 14 terminations. High-quality output is provided by the electronic component's 2 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 14 series that this electronic component is included. Unlike digital switches, these are based on SPDT switching circuits. 1 circuits are used in this analogue multiplexer. This digital multiplexer has 50Ohm internal resistance. You can find the functions of the 14 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 36V volts for the multiplexer. It is recommended that the electrical component receives a voltage of 10V. It may damage the digital multiplexer if the voltage is higher than 500μA. For this switch, a dual supply voltage is feasible, but it must not exceed 18VFor dual power supplies, a voltage of at least 5V should be attached. 15V operating voltages are supported by the electronic component.
DG301AAK/883B Features
2 Channels
Switch Circuit: SPDT
DG301AAK/883B Applications
There are a lot of Maxim Integrated DG301AAK/883B Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Industrial
- SONET/SDH ADM
- Channelized and Unchannelized DS3 applications
- Communication systems
- MP3 players
- High reliability control systems
- Isolation
- Signal routing between systems
- Medical
