DG301ACJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG301A |
| Pin Count | 14 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Max Supply Voltage | 25V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG301ACJ+ Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tube. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 2:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 14. By its 1 channels, the electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 14 pins are injected into the body of the electronic part. A SPDT switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with DG301A. There is 50Ohm internal resistance in this digital multiplexer. For functions related to 14 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 25V. Dual, Single supply type digital switch with a low cost. It would be sufficient to run this analogue multiplexer with 230μA current. A digital multiplexer may suffer damage if voltage is applied above 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. In the case of dual power supplies, you should connect at least 5V. 18V operating voltages are supported by the electronic component.
DG301ACJ+ Features
1 Channels
Switch Circuit: SPDT
230μA Supply Current
DG301ACJ+ Applications
There are a lot of Maxim Integrated DG301ACJ+ Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- SDH
- Medical
- Multiplexers
- Audio/video switches
- Video switching
- Audio and video signal routing
- T1/E1 Terminals
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio and video routing
