DG301ACWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG301A |
| Pin Count | 16 |
| Number of Channels | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 230μA |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG301ACWE+ Overview
Packed in 16-SOIC (0.295, 7.50mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Around 0°C~70°C TA is the extended operating temperature. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. The electronic part body is injected with 16 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. Using the DG301A search parameter, you can discover variants of the switch. A 50Ohm internal resistance characterizes this multiplexer. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 18V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. 5V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer could operate on 230μA current. It may damage the digital multiplexer if the voltage is higher than 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. With dual power supplies, you should attach at least 5V.
DG301ACWE+ Features
1 Channels
Switch Circuit: SPDT
230μA Supply Current
DG301ACWE+ Applications
There are a lot of Maxim Integrated DG301ACWE+ Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Battery-powered systems
- Relay Replacement
- Central office
- Audio and video signal routing
- Fiber In The Loop (FITL)
- Avionics and Military Systems
- Avionics
- RGB switches
- Mechanical reed relay replacement
