DG302AAK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Screening Level | MIL-STD-883 Class B |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 5.08mm |
| Length | 19.43mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG302AAK/883B Overview
The electrical component comes in 14-CDIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Through Hole position. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -55°C~125°C TA. A total of 14 terminations have been recorded. High-quality output is provided by the electronic component's 2 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 14 series. On the other hand, analog switches can be constructed using DPST - NO switching circuits. The multiplexer consists of 2 circuits. It has an internal resistance of 50Ohm. You can find the functions of the 14 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 36V to a switch device. A low voltage of 10V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 500μA. Despite this switch's dual supply capability, its voltage should not exceed 18V. A dual power supply should have at least 5V voltage attached. The electronic component can function from 15V.
DG302AAK/883B Features
2 Channels
Switch Circuit: DPST - NO
DG302AAK/883B Applications
There are a lot of Maxim Integrated DG302AAK/883B Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- Relay Replacement
- Ultrasound
- Video signal routing
- Multi-Line E1 Interface Cards
- Cable PC
- DSUs
- High-Voltage
- Microprocessor Controlled Analog Systems
- Remote Powered Equipment
