DG302ACWE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 450mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG302A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 25V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 230μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 10μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG302ACWE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.295, 7.50mm Width). High reliability is ensured by the advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Extended operating temperature around 0°C~70°C TA. There are 16 terminations totally. As a result of its 2 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. A key feature of the 16 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using DPST - NO switching circuits. This multiplexer is composed of 2 circuits. Try searching for DG302A variants of the analog switch ic. In this multiplexer, the internal resistance is 50Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 25V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. It is recommended that the electrical component receives a voltage of 4V. An operating current of 230μA would be sufficient for this switch device. Putting voltage greater than 10μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. The voltage should be at least 5V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG302ACWE+ Features
2 Channels
Switch Circuit: DPST - NO
230μA Supply Current
DG302ACWE+ Applications
There are a lot of Maxim Integrated DG302ACWE+ Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Cable PC
- Fiber In The Loop (FITL)
- Multi-Line E1 Interface Cards
- Relay replacements
- CSU
- Isolation
- Signal routing between systems
- Precision instrumentation
- RGB switches
