DG302BDJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 50Ohm |
| Max Power Dissipation | 470mW |
| Reach Compliance Code | unknown |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 8pC |
| Crosstalk | -74dB @ 500kHz |
| Drain to Source Resistance | 50Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG302BDJ Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. Through Hole is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. There is an electrical component included in the 14 series. A DPST - NO switching circuit is used to build these analog multiplexers. The multiplexer consists of 2 circuits. In this multiplexer, the internal resistance is 50Ohm. For functions related to 14 pins, please refer to the datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. If you put voltage higher than 1mA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. You should attach at least 7V voltage if you are using dual power supply. This electrical part is compatible with 15V operating voltages. There are 4 inputs to be operated. This electronic component presents a Drain to Source resistance of 50Ohm.
DG302BDJ Features
Switch Circuit: DPST - NO
Drain-to-Source resistance: 50Ohm
DG302BDJ Applications
There are a lot of Vishay Siliconix DG302BDJ Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Automotive applications
- Multi-Line E1 Interface Cards
- High-Voltage
- High reliability control systems
- Transmit
- SDH
- MP3 players
- DSLAMs
- SONET/SDH ADM
