DG303AAK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Lead, Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 14 |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | -10μA |
| Power Dissipation | 727mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 500 ns |
| Number of Inputs | 4 |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Screening Level | MIL-STD-883 Class B |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 5.08mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG303AAK/883B Overview
Shipping overseas is convenient with the electronic component packed in 14-CDIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. Through Hole is where this multiplexer is located. 2:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of -55°C~125°C TA degrees Celsius. The total number of terminations is 14. As a result of its 2 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. Circuits based on SPDT switching are used to construct these analog switch ics. This multiplexer is composed of 2 circuits. In this multiplexer, the internal resistance is 50Ohm. The functions of 14 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. It is recommended to use 10V as the lowest voltage for the electrical part. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. You should attach at least 5V voltage if you are using dual power supply. Operating 4 inputs is required.
DG303AAK/883B Features
2 Channels
Switch Circuit: SPDT
DG303AAK/883B Applications
There are a lot of Maxim Integrated DG303AAK/883B Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- 65 V DACs
- PBX interfaces
- Battery Powered Systems
- USB 1.1 signal switching circuits
- SDH
- Medical systems
- Residential Gateways, Home Gateway/Router
- Avionics test equipment
- Public switching systems
