DG303ACJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2005 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG303A |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 230μA |
| Max Supply Current | 500μA |
| Turn On Delay Time | 300 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 30Ohm |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG303ACJ+ Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, this analog switch is mounted. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to 0°C~70°C TA. A total of 14 terminations have been recorded. A 4 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. The electrical component body receives 14 pins. The analog switch ics are built using SPDT switching circuits. A total of 2 circuits make up this switch device. Search with DG303A if you are looking for analog multiplexer variants. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. The datasheets for the 14 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. A low voltage of 10V should be applied to the electronic component. For this multiplexer to operate, 230μA current would be sufficient. The analogue multiplexer may be damaged if voltage is greater than 500μA. For this switch, a dual supply voltage is feasible, but it must not exceed 18VA dual power supply should have at least 5V voltage attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Drain to Source resistance for this electronic component is 30Ohm.
DG303ACJ+ Features
4 Channels
Switch Circuit: SPDT
230μA Supply Current
Drain-to-Source resistance: 30Ohm
DG303ACJ+ Applications
There are a lot of Maxim Integrated DG303ACJ+ Analog Switches & Multiplexers ICs applications.
- Precision data acquisition
- Cable Modem
- DSLAMs
- Audio signal routing
- Audio and video routing
- Cell phones
- Industrial and process control systems
- PDH Multiplexers
- Switching Systems
- E1 Multiplexer
