Parameters |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
50Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
450mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG303A |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
18V |
Number of Channels |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
230μA |
Nominal Supply Current |
230μA |
Max Supply Current |
230μA |
Turn On Delay Time |
300 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
50Ohm |
Min Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
5nA |
Channel Capacitance (CS(off), CD(off)) |
14pF 14pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
300ns, 250ns |
Charge Injection |
12pC |
Crosstalk |
-74dB @ 500kHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
50Ohm |
Voltage - Supply, Dual (V±) |
±5V~18V |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.295, 7.50mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2008 |
DG303ACWE+ Overview
This electronic part is conveniently packaged in 16-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around 0°C~70°C TA extended. There are 16 terminations totally. As a result of its 2 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 16 pins are injected into the electrical part body. Based on SPDT switching circuits, these analog multiplexers work. Try searching for the analog switch ic with DG303A if you are looking for variants. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 30V voltage to the switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 10V voltage fed to the electrical part below 10V. This multiplexer would work with 230μA current. Put voltage above 230μA on the multiplexer to cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 18V. If you are using dual power supplies, you should attach at least 5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages of 18V are compatible with the electrical part. This electronic component presents a Drain to Source resistance of 50Ohm.
DG303ACWE+ Features
2 Channels
Switch Circuit: SPDT
230μA Supply Current
Drain-to-Source resistance: 50Ohm
DG303ACWE+ Applications
There are a lot of Maxim Integrated DG303ACWE+ Analog Switches & Multiplexers ICs applications.
- Medical systems
- Isolation
- Fiber to the Home
- Microwave transmission systems
- Switching Systems
- Audio and video switching
- Battery Powered Instruments
- Avionics and Military Systems
- Audio/video switches
- SONET