Parameters |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG303A |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
28V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Operating Supply Current |
230μA |
Nominal Supply Current |
230μA |
Max Supply Current |
500μA |
Turn On Delay Time |
300 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
18V |
On-State Resistance (Max) |
50Ohm |
Min Dual Supply Voltage |
5V |
High Level Output Current |
30mA |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
5nA |
Channel Capacitance (CS(off), CD(off)) |
14pF 14pF |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
300ns, 250ns |
Charge Injection |
12pC |
Crosstalk |
-74dB @ 500kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Dual (V±) |
±5V~18V |
Length |
10.3mm |
Width |
7.5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.295, 7.50mm Width) |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
50Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
DG303ACWE+T Overview
Packed in 16-SOIC (0.295, 7.50mm Width), the electronic component is convenient for shipping overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operation at a temperature around 0°C~70°C TA. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. Into the electrical component body are injected 16 pins. These analog multiplexers are built based on SPDT switching circuits. The circuits in this analogue multiplexer number 2. Using the DG303A search parameter, you can discover variants of the switch. Analog switches have 50Ohm internal resistance. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. An effective Dual, Single supply digital multiplexer. It is recommended to use 10V as the lowest voltage for the electrical part. The switch device would be able to operate with 230μA current. The analogue multiplexer may be damaged if voltage is greater than 500μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. If you are using dual power supplies, you should attach at least 5V. 28V operating voltages are supported by the electronic component.
DG303ACWE+T Features
1 Channels
Switch Circuit: SPDT
230μA Supply Current
DG303ACWE+T Applications
There are a lot of Maxim Integrated DG303ACWE+T Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Data Acquisition Systems
- ATM
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fiber to the Home
- E1 Network Equipment
- Residential Gateways, Home Gateway/Router
- Power routing
- Industrial and process control systems