DG303BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 50Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Polarity | Non-Inverting |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Analog IC - Other Type | SPST |
| Operating Supply Current | 230μA |
| Power Dissipation | 470mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 150 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 130 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 100mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 300ns, 250ns |
| Charge Injection | 8pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 50Ohm |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG303BDJ Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a number of circuits 2:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 14. Powered by a 15V voltage supply, the electrical part should be switched on and run. 14 pins are injected to the electronic part body. DPST - NO/NC switching circuits are used in these analog switch ics. The circuits in this analogue multiplexer number 2. Analog switches have 50Ohm internal resistance. For functions related to 14 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. The switch device would be able to operate with 230μA current. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. It is integrated with SPST analog ICs. A voltage of 15V can be used to operate the electronic component. The electrical component supports 4 inputs. Resistivity from Drain to Source is 50Ohm for this electronic part.
DG303BDJ Features
Switch Circuit: DPST - NO/NC
230μA Supply Current
Drain-to-Source resistance: 50Ohm
DG303BDJ Applications
There are a lot of Vishay Siliconix DG303BDJ Analog Switches & Multiplexers ICs applications.
- DSLAMs
- USB 1.1 signal switching circuits
- Low-Voltage
- Industrial and process control systems
- Switching Systems
- Microwave transmission systems
- Public switching systems
- Video signal routing
- Communications systems
- Sample hold systems
