DG303BDJ-E3

300ns, 250ns DPST - NO/NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG303 14 Pins 1nA 15V 14-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG303BDJ-E3
Package: 14-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 728
Description: 300ns, 250ns DPST - NO/NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG303 14 Pins 1nA 15V 14-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	14-DIP (0.300, 7.62mm)
Number of Pins	14
Weight	1.620005g
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2005
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	14
Resistance	50Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	470mW
Technology	CMOS
Number of Functions	2
Supply Voltage	15V
Base Part Number	DG303
Output	SEPARATE OUTPUT
Pin Count	14
Operating Supply Voltage	15V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	230μA
Nominal Supply Current	230μA
Power Dissipation	470mW
Max Supply Current	1mA
Throw Configuration	DPST, SPDT
Turn On Delay Time	150 ns
Number of Inputs	4
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	130 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	50Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	62 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	14pF 14pF
Switch Circuit	DPST - NO/NC
Switch Time (Ton, Toff) (Max)	300ns, 250ns
Charge Injection	8pC
Crosstalk	-74dB @ 500kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	30Ohm
Voltage - Supply, Dual (V±)	±15V
Height Seated (Max)	5.08mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG303BDJ-E3 Overview

The electronic part can be shipped overseas conveniently because it is packaged in 14-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 14 terminations. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. There is an electrical component included in the 14 series. A DPST - NO/NC switching circuit is used for these analog switches. The multiplexer consists of 2 circuits. Using the DG303 search parameter, you can discover variants of the switch. This digital multiplexer has 50Ohm internal resistance. For details about the functions of 14 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 13V. In order to operate this switch device, it would need a current of 230μA. Put voltage above 1mA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 7V to your dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 15V operating voltages can be used with this electrical part. The electrical component supports 4 inputs. Resistivity from Drain to Source is 30Ohm for this electronic part.