DG303BDY-E3

300ns, 250ns DPST - NO/NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG303 14 Pins 1nA 15V 14-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG303BDY-E3
Package: 14-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 355
Description: 300ns, 250ns DPST - NO/NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG303 14 Pins 1nA 15V 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	14-SOIC (0.154, 3.90mm Width)
Number of Pins	14
Weight	338.011364mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	14
Resistance	50Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG303
Output	SEPARATE OUTPUT
Pin Count	14
Qualification Status	Not Qualified
Operating Supply Voltage	15V
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	230μA
Nominal Supply Current	230nA
Power Dissipation	600mW
Max Supply Current	1mA
Throw Configuration	DPST, SPDT
Turn On Delay Time	150 ns
Number of Inputs	4
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	130 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	50Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	62 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	14pF 14pF
Switch Circuit	DPST - NO/NC
Switch Time (Ton, Toff) (Max)	300ns, 250ns
Charge Injection	8pC
Crosstalk	-74dB @ 500kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	30Ohm
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	8.75mm
Width	4mm
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG303BDY-E3 Overview

Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Increasing operating temperature to around -40°C~85°C TA. 14 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 14 pins are injected into the electrical part body. Unlike digital switches, these are based on DPST - NO/NC switching circuits. Circuits number 2 make up this analogue multiplexer. Try searching for the analog switch ic with DG303 if you are looking for variants. An switch multiplexer with 50Ohm internal resistance has a value of 50Ohm. Datasheets for functions of 14 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 36V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage the electronic part should receive is 13V. It would be sufficient to run this analogue multiplexer with 230μA current. When the digital multiplexer is charged above 1mA, damage can occur. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 7V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages of 15V are compatible with the electrical part. Operating 4 inputs is required. Drain to Source resistance for this electronic component is 30Ohm.