DG304ACJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG304A |
| Pin Count | 14 |
| Number of Channels | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 19.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG304ACJ+ Overview
Presented in 14-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around 0°C~70°C TA. Total terminations are 14. Due to its 2 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of the design of the 14 series, this electronic part has been incorporated into the system. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with DG304A if you're looking for variants. This digital multiplexer has 50Ohm internal resistance. Datasheets for functions of 14 pins are available. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 10V voltage fed to the electrical part below 10V. This digital switch can be operated with a current of 1nA. It may damage the digital multiplexer if the voltage is higher than 10μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. With dual power supplies, you should attach at least 5V.
DG304ACJ+ Features
2 Channels
Switch Circuit: SPST - NO
1nA Supply Current
DG304ACJ+ Applications
There are a lot of Maxim Integrated DG304ACJ+ Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- Audio and video signal routing
- DSUs
- T1/E1 Terminals
- Communication systems
- DSLAMs
- Industrial
- PBXs
- Mechanical reed relay replacement
- Ultrasound
