DG305ACJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG305A |
| Pin Count | 14 |
| Number of Channels | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 10μA |
| Turn On Delay Time | 250 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG305ACJ+ Overview
The electronic component is convenient to ship overseas because it is packed in a 14-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 2:1. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 14. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 14 series. A SPDT switching circuit is used for these analog switches. Try searching for DG305A variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 50Ohm. For details about the functions of 14 pins, please refer to the datasheets. Multiplexers should not be powered above 18V in normal situations. The digital multiplexer has a low cost Dual, Single supply. There should be 5V voltage fed to the electrical part below 5V. This multiplexer would work with 1nA current. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 18V. If you are using dual power supplies, you should attach at least 5V.
DG305ACJ+ Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
DG305ACJ+ Applications
There are a lot of Maxim Integrated DG305ACJ+ Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Automatic test equipment
- Frame Relay Equipment
- RGB switches
- Public switching systems
- ISDN NT1/TA
- Ultrasound
- Mechanical reed relay replacement
- Digital access cross connects
- Medical Instrumentation
