DG306AAK/883
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 14-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | +-15V |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Screening Level | 38535Q/M;38534H;883B |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 30pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG306AAK/883 Overview
This electronic part is conveniently packaged in 14-CDIP (0.300, 7.62mm), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Through Hole position. 2:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -55°C~125°C TA. A total of 14 terminations have been recorded. With a 15V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 14 pins. On the other hand, analog switches can be constructed using DPST - NO switching circuits. There are 2 circuits in this switch device. As far as internal resistance is concerned, it has 50Ohm. You can find the functions of the 14 pins in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. It is recommended that the electrical component receives a voltage of 13V. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 7V voltage attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
DG306AAK/883 Features
Switch Circuit: DPST - NO
DG306AAK/883 Applications
There are a lot of Vishay Siliconix DG306AAK/883 Analog Switches & Multiplexers ICs applications.
- Industrial
- Cable PC
- Medical systems
- Precision test equipment
- USB 1.1 signal switching circuits
- Optical Applications
- Fault Tolerant Systems
- Audio signal routing
- High-Voltage
- Relay replacements
