DG306BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Weight | 1.620005g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | DG306 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Max Supply Current | 100μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 110 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 70 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 70ns (Typ) |
| Charge Injection | 30pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 19.3mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG306BDJ-E3 Overview
Packed in 14-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. In total, 14 terminations have occurred. A 1 channel electronic part produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. The electronic part body is injected with 14 pins. The analog switch ics are built using DPST - NO switching circuits. The circuits in this analogue multiplexer number 2. Try searching with DG306 if you're looking for variants. It has an internal resistance of 50Ohm. To find out what the 14 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 13V should be applied to the electronic component. For this digital switch to work, 1nA current would suffice. A voltage higher than 100μA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. You should attach at least 7V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 15V operating voltages can be used with this electrical part.
DG306BDJ-E3 Features
1 Channels
Switch Circuit: DPST - NO
1nA Supply Current
DG306BDJ-E3 Applications
There are a lot of Vishay Siliconix DG306BDJ-E3 Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- DSLAMs
- Microwave transmission systems
- Low-Voltage
- Wireless Local Loop
- Battery Powered Instruments
- Transmit
- High reliability control systems
- Automotive applications
- Channelized and Unchannelized DS3 applications
