banner_page

DG307AAK

250ns, 150ns SPDT 50Ohm Analog Switches BREAK-BEFORE-MAKE 14 Pins 15V 14-CDIP (0.300, 7.62mm)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG307AAK
  • Package: 14-CDIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 209
  • Description: 250ns, 150ns SPDT 50Ohm Analog Switches BREAK-BEFORE-MAKE 14 Pins 15V 14-CDIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 14-CDIP (0.300, 7.62mm)
Number of Pins 14
Operating Temperature -55°C~125°C TA
Packaging Tube
Published 2005
JESD-609 Code e0
Pbfree Code no
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
Resistance 50Ohm
Terminal Finish Tin/Lead (Sn/Pb)
Subcategory Multiplexer or Switches
Max Power Dissipation 825mW
Technology CMOS
Number of Functions 2
Supply Voltage 15V
Pin Count 14
Number of Outputs 4
Operating Supply Voltage 15V
Number of Circuits 2
Max Supply Voltage 36V
Min Supply Voltage 13V
Nominal Supply Current 1nA
Power Dissipation 825mW
Max Supply Current 10μA
Turn On Delay Time 250 ns
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 150 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 50Ohm
Min Dual Supply Voltage 7V
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 2:1
Channel Capacitance (CS(off), CD(off)) 14pF 14pF
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 250ns, 150ns
Charge Injection 30pC
Crosstalk -74dB @ 500kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Dual (V±) ±15V
Radiation Hardening No
RoHS Status Non-RoHS Compliant

DG307AAK Overview


The electrical component comes in 14-CDIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexers and demultiplexers have the same number of circuits 2:1. Increasing operating temperature to around -55°C~125°C TA. In total, there have been 14 terminations. An 15V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 14 series that this electronic component is included. Based on SPDT switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 2. Analog switches have 50Ohm internal resistance. Please refer to the datasheets for 14 pins functions. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. It may damage the digital multiplexer if the voltage is higher than 10μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. For dual power supplies, a voltage of at least 7V should be attached. The electronic component can function from 15V. A analog switch ics with 4 outputs is included.

DG307AAK Features


Switch Circuit: SPDT

DG307AAK Applications


There are a lot of Vishay Siliconix DG307AAK Analog Switches & Multiplexers ICs applications.

  • Relay replacements
  • Avionics
  • Cable Modem
  • Medical
  • Multi-Line E1 Interface Cards
  • Data switching
  • Microwave transmission systems
  • Industrial
  • Industrial and process control systems
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads

Write a review

Note: HTML is not translated!
    Bad           Good