DG307ACWE
| Parameters | |
|---|---|
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 50Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG307A |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 1nA |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 14pF 14pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | 12pC |
| Crosstalk | -74dB @ 500kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 150ns |
| Voltage - Supply, Dual (V±) | ±5V~18V |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
DG307ACWE Overview
Presented in 16-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. In total, 16 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SPDT switching circuits. The multiplexer consists of 2 circuits. Use DG307A to search for variants of the digital switches. Analog switches have 50Ohm internal resistance. In this analog multiplexer, the value is Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Dual supply type digital switch with a low cost. 10V should be the lowest voltage fed to the electronic component. For this multiplexer to operate, 1nA current would be sufficient. Despite this switch device's dual supply capability, its voltage should not exceed 18V. A dual power supply should have at least 5V voltage attached. This analog switch ic utilizes SEPARATE OUTPUT output.
DG307ACWE Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
DG307ACWE Applications
There are a lot of Maxim Integrated DG307ACWE Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- Cross Connects
- Voice over IP/DSL – Integrated Access Devices, Smart
- SONET/SDH ADM
- Video switching
- Mechanical reed relay replacement
- Residential Gateways, Home Gateway/Router
- Channelized and Unchannelized DS3 applications
- Industrial
- Imaging
