DG308ACJ+
| Parameters | |
|---|---|
| Min Supply Voltage | 5V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | -10pC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG308A |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 20V |
DG308ACJ+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. Through Hole is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around 0°C~70°C TA are extended for operation. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Based on SPST - NO switching circuits, these analog multiplexers work. If you are looking for variants of the digital switch, trying search with DG308A. There is 100Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. A voltage higher than 20V should not normally be supplied to the switches. A cost-effective Dual supply type analogue multiplexer. A low voltage of 5V should be applied to the electronic component. For this digital switch to work, 1nA current would suffice. Put voltage above 100μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 5V.
DG308ACJ+ Features
4 Channels
Switch Circuit: SPST - NO
1nA Supply Current
DG308ACJ+ Applications
There are a lot of Maxim Integrated DG308ACJ+ Analog Switches & Multiplexers ICs applications.
- Imaging
- Cable Modem
- Sample hold systems
- Routers
- Frame Relay Equipment
- SDH/SONET multiplexers
- Video signal routing
- Remote Powered Equipment
- PBXs
- ATM
