DG308ACJ-E3
| Parameters | |
|---|---|
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG308 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 10μA |
| Power Dissipation | 470mW |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | -10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2015 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
DG308ACJ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around 0°C~70°C TA are extended for operation. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. The electronic part body is injected with 16 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with DG308 to find analog multiplexer variants. There is 100Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage the electronic part should receive is 13V. 10μA current would be enough for this multiplexer to operate. If you put voltage higher than 10μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. This electrical part is compatible with 15V operating voltages. The electrical component supports 4 inputs.
DG308ACJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
DG308ACJ-E3 Applications
There are a lot of Vishay Siliconix DG308ACJ-E3 Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- USB 1.1 signal switching circuits
- DSUs
- High speed data transmission line cards
- Imaging
- Voice over IP/DSL – Integrated Access Devices, Smart
- DVD-R
- 65 V DACs
- PCMCIA cards
- PBXs
