DG308ADY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG308 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 10μA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 600mW |
| Max Supply Current | 10μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | -10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG308ADY-E3 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Into the electrical component body are injected 16 pins. The analog switch ics are built using SPST - NO switching circuits. It consists of 4 circuits. Using the DG308 search parameter, you can discover variants of the switch. This digital multiplexer has 100Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 13V. It would be sufficient to run this analogue multiplexer with 10μA current. When the digital multiplexer is charged above 10μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 22VThe voltage should be at least 7V if you are using dual power supplies. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages of 15V are compatible with the electrical part. The 4 inputs need to be operated in order to work.
DG308ADY-E3 Features
1 Channels
Switch Circuit: SPST - NO
10μA Supply Current
DG308ADY-E3 Applications
There are a lot of Vishay Siliconix DG308ADY-E3 Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- HDTV
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- ATM
- Communications systems
- FTTH
- PCMCIA cards
- SDH/SONET multiplexers
- Imaging
- E1 Multiplexer
