DG308ADY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Nominal Supply Current | 1nA |
| Power Dissipation | 600mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | -10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Voltage - Supply, Dual (V±) | ±15V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG308ADY-T1 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 16. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a SPST - NO switching circuit are built. The multiplexer consists of 4 circuits. There is 100Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 36V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 13V as the lowest voltage for the electrical part. It may damage the digital multiplexer if the voltage is higher than 10μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 7V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. A voltage of 15V can be used to operate the electronic component. Among the inputs that can be operated are the 4 inputs.
DG308ADY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG308ADY-T1 Applications
There are a lot of Vishay Siliconix DG308ADY-T1 Analog Switches & Multiplexers ICs applications.
- DVD-R
- SONET/SDH ADM
- PDH Multiplexers
- HDTV
- ATM
- Routers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical
- Multiplexers
- PCMCIA cards
