DG308BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Power Dissipation | 470mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
DG308BDJ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. This analog switch is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. In total, there have been 16 terminations. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 16 series. Circuits based on SPST - NO switching are used to construct these analog switch ics. There is 85Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 44V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. There should be 4V voltage fed to the electrical part below 4V. A digital multiplexer may suffer damage if voltage is applied above 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 4V voltage attached. This analog switch ic utilizes SEPARATE OUTPUT output. Among the inputs that can be operated are the 4 inputs. Drain to Source resistance is 85Ohm.
DG308BDJ Features
Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm
DG308BDJ Applications
There are a lot of Vishay Siliconix DG308BDJ Analog Switches & Multiplexers ICs applications.
- Frame Relay Equipment
- Audio and video switching
- New designs requiring multiplexer functions
- Imaging
- Sample-and-hold systems
- Ultrasound
- Medical Instrumentation
- Communication systems
- Cable PC
- SONET/SDH ADM
