Parameters |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.635mm |
Reach Compliance Code |
unknown |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
+-15V |
Number of Circuits |
4 |
Max Supply Voltage |
44V |
Min Supply Voltage |
4V |
Voltage - Supply, Single/Dual (±) |
4V~44V ±4V~22V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
200ns, 150ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1.7 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
200ns |
Normal Position |
NO |
RoHS Status |
Non-RoHS Compliant |
DG308BDQ Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used to build these analog multiplexers. It consists of 4 circuits. Internally, this switch multiplexer has a resistance of 85Ohm. Datasheets for 16 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 44V. There should be 4V voltage fed to the electrical part below 4V. There is no problem with using dual supply voltage, but it should not exceed 22V. In the case of dual power supplies, you should connect at least 4V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG308BDQ Features
Switch Circuit: SPST - NO
DG308BDQ Applications
There are a lot of Vishay Siliconix DG308BDQ Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- SONET
- RGB switches
- PBXs
- Fault Tolerant Systems
- Cable PC
- Cell phones
- Optical Applications
- High reliability control systems
- Cable Modem