DG308BDQ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG308 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1.7Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Switch-off Time-Max | 150ns |
| Normal Position | NO |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
DG308BDQ-E3 Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Circuits number 4 make up this analogue multiplexer. Try searching with DG308 if you're looking for variants. Analog switches have 160Ohm internal resistance. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 44V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 4V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. The voltage should be at least 4V if you are using dual power supplies. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
DG308BDQ-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG308BDQ-E3 Applications
There are a lot of Vishay Siliconix DG308BDQ-E3 Analog Switches & Multiplexers ICs applications.
- MP3 players
- Multi-Line E1 Interface Cards
- High speed data transmission line cards
- PBXs
- ATM
- Relay replacements
- Isolation
- Multiplexers
- Data Acquisition Systems
- Digital cross connects (DSX-1)
