DG308BDQ-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15/12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1.7Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 85Ohm |
| Normal Position | NO |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
DG308BDQ-T1 Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 16 series. A SPST - NO switching circuit is used for these analog switches. A total of 4 circuits make up this switch device. A 85Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 44V in normal situations. An effective Dual, Single supply digital multiplexer. 4V is the lowest voltage that should be fed to the electronic electronic part. A digital multiplexer may suffer damage if voltage is applied above 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. In the case of dual power supplies, you should connect at least 4V. This analog switch ic utilizes SEPARATE OUTPUT output. This electronic component presents a Drain to Source resistance of 85Ohm.
DG308BDQ-T1 Features
1 Channels
Switch Circuit: SPST - NO
Drain-to-Source resistance: 85Ohm
DG308BDQ-T1 Applications
There are a lot of Vishay Siliconix DG308BDQ-T1 Analog Switches & Multiplexers ICs applications.
- Avionics
- Microprocessor Controlled Analog Systems
- Frame Relay Equipment
- Channelized and Unchannelized DS3 applications
- DSLAMs
- Switching Systems
- PBXs
- Imaging
- Communication systems
- Multi-Line E1 Interface Cards
