DG308BDY-T1
| Parameters | |
|---|---|
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15/12V |
| Number of Channels | 1 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1.7Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 150ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
DG308BDY-T1 Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is part of the design of the 16 series that this electronic component is included. The analog switch ics are built using SPST - NO switching circuits. In this multiplexer, the internal resistance is 85Ohm. You can find the functions of the 16 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 44V to a switch device. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 4V. It may damage the digital multiplexer if the voltage is higher than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using dual power supplies, you should attach at least 4V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. There are 4 inputs to be operated.
DG308BDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG308BDY-T1 Applications
There are a lot of Vishay Siliconix DG308BDY-T1 Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- CSU
- New designs requiring multiplexer functions
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Voice over IP/DSL – Integrated Access Devices, Smart
- Transmit
- Audio/video switches
- Avionics and Military Systems
- 65 V DACs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
