Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG308 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
+-15/12V |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
4V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Power Dissipation |
640mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
200 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4V~44V ±4V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
1.7Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
200ns, 150ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1.7 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
85Ohm |
Normal Position |
NO |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG308BDY-T1-E3 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. 16 pins are injected to the electronic part body. SPST - NO switching circuits are used in these analog switch ics. Try searching for the analog switch ic with DG308 if you are looking for variants. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. Please refer to the datasheets for 16 pins functions. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 44V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Dual, Single supply type. 4V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. It may damage the digital multiplexer if the voltage is higher than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. For dual power supplies, a voltage of at least 4V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating 4 inputs is required. It has a Drain to Source resistance of 85Ohm ohms.
DG308BDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Drain-to-Source resistance: 85Ohm
DG308BDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG308BDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- CSU
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- SONET
- Intelligent PBX
- Mechanical reed relay replacement
- Cable PC
- Channelized and Unchannelized DS3 applications
- Industrial control systems
- Precision test equipment