Parameters |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tube |
Published |
1996 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Tin/Lead (Sn/Pb) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
30V |
Min Supply Voltage |
5V |
Voltage - Supply, Single/Dual (±) |
5V~30V ±5V~20V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
100Ohm |
Min Dual Supply Voltage |
4.5V |
Screening Level |
MIL-STD-883 Class B |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
78 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
11pF 8pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
250ns, 150ns |
Charge Injection |
-10pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
200ns |
Switch-off Time-Max |
150ns |
Normal Position |
NC |
Height Seated (Max) |
5.08mm |
Width |
7.62mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
DG309AK/883B Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -55°C~125°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the electrical part body. A SPST - NC switching circuit is used for these analog switches. A total of 4 circuits make up this switch device. Analog switches have 100Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 30V should not normally be supplied to the switches. It is recommended to use 5V as the lowest voltage for the electrical part. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
DG309AK/883B Features
1 Channels
Switch Circuit: SPST - NC
DG309AK/883B Applications
There are a lot of Maxim Integrated DG309AK/883B Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable Modem
- Industrial control systems
- Channelized and Unchannelized DS3 applications
- Medical
- Private Branch Exchange (PBX)
- Mechanical reed relay replacement
- Medical Instrumentation
- Residential Gateways, Home Gateway/Router
- Public switching systems