DG309BDQ-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG309 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1.7Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Switch-off Time-Max | 150ns |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG309BDQ-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tube is used to provide high reliability. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. There are 4 circuits in this multiplexer. Using the DG309 search parameter, you can discover variants of the switch. There is 160Ohm internal resistance in this digital multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 44V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4V is the lowest voltage the electrical component should receive. The switch device would be able to operate with 1μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. If you are using dual power supplies, you should attach at least 4V. There are SEPARATE OUTPUT outputs on this analog switch ic.
DG309BDQ-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG309BDQ-E3 Applications
There are a lot of Vishay Siliconix DG309BDQ-E3 Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- High reliability control systems
- Digital cross connects (DSX-1)
- 65 V DACs
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial
- Multiplexers
- New designs requiring multiplexer functions
- Relay replacements
