Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Power Supplies |
+-15/12V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
44V |
Min Supply Voltage |
4V |
Max Supply Current |
1μA |
Turn On Delay Time |
200 ns |
Voltage - Supply, Single/Dual (±) |
4V~44V ±4V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
1.7Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
200ns, 150ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1.7 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height |
920μm |
Length |
5.08mm |
Width |
4.4mm |
RoHS Status |
Non-RoHS Compliant |
DG309BDQ-T1 Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. 4 circuits are used in this analogue multiplexer. Internally, this switch multiplexer has a resistance of 85Ohm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 44V to a switch device. An effective Dual, Single supply digital multiplexer. 4V should be the lowest voltage fed to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 4V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG309BDQ-T1 Features
1 Channels
Switch Circuit: SPST - NC
DG309BDQ-T1 Applications
There are a lot of Vishay Siliconix DG309BDQ-T1 Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- High speed data transmission line cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Battery-powered systems
- CSU
- Industrial control systems
- Frame Relay Equipment
- Audio/video switches
- Modems
- RGB switches