DG309BDQ-T1-E3

200ns, 150ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG309 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG309BDQ-T1-E3
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 751
Description: 200ns, 150ns SPST - NC 85Ohm Analog Switches BREAK-BEFORE-MAKE DG309 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Weight	172.98879mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	160Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG309
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	+-15/12V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	44V
Min Supply Voltage	4V
Operating Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	200 ns
Voltage - Supply, Single/Dual (±)	4V~44V ±4V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	150 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	85Ohm
Min Dual Supply Voltage	4V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	1.7Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	200ns, 150ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	1.7 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NC
Height	920μm
Length	5.08mm
Width	4.4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

DG309BDQ-T1-E3 Overview

This electronic part is conveniently packaged in 16-TSSOP (0.173, 4.40mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. The total number of terminations is 16. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. Into the electrical component body are injected 16 pins. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with DG309 if you are looking for variants. It has an internal resistance of 160Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 44V to a switch device. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 4V. 1μA current would be enough for this multiplexer to operate. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using a dual power supply, you should attach at least 4V. There are SEPARATE OUTPUT outputs on this analog switch ic.