DG309BDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15V |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Drain to Source Resistance | 100Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG309BDY Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. There are 16 terminations totally. Turning on and running the electrical part should be easy with a 15V voltage supply. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NC switching are used to construct these analog switch ics. Circuits number 4 make up this analogue multiplexer. Analog switches have 85Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 44V voltage to the switch device. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended to use 4V as the lowest voltage for the electrical part. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. You should attach at least 4V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A Drain to Source resistance of 100Ohm is shown for this electronic part.
DG309BDY Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 100Ohm
DG309BDY Applications
There are a lot of Vishay Siliconix DG309BDY Analog Switches & Multiplexers ICs applications.
- PDAs
- Cable PC
- ATM
- Residential Gateways, Home Gateway/Router
- Audio signal routing
- Microprocessor controlled systems
- Cross Connects
- Channel Banks
- Routers
- Ultrasound
