DG309BDY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | +-15/12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 4V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1.7Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 150ns |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
DG309BDY-T1 Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Circuits based on SPST - NC switching are used to construct these analog switch ics. There are 4 circuits in this multiplexer. There is 85Ohm internal resistance in this digital multiplexer. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 44V to a switch device. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 4V. The analogue multiplexer may be damaged if voltage is greater than 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. You should attach at least 4V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
DG309BDY-T1 Features
1 Channels
Switch Circuit: SPST - NC
DG309BDY-T1 Applications
There are a lot of Vishay Siliconix DG309BDY-T1 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- High-Voltage
- Multi-Line E1 Interface Cards
- PDH Multiplexers
- High reliability control systems
- Modems
- Industrial
- High speed data transmission line cards
- Avionics
- T1/E1 Terminals
