Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG309 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
+-15/12V |
Number of Channels |
1 |
Max Supply Voltage |
44V |
Min Supply Voltage |
4V |
Operating Supply Current |
1μA |
Power Dissipation |
640mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
300 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
4V~44V ±4V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
200 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
1.7Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
200ns, 150ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1.7 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
150ns |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG309BDY-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 16 series. Circuits based on SPST - NC switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with DG309. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 44V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. It is recommended to use 4V as the lowest voltage for the electrical part. This multiplexer would work with 1μA current. Putting voltage greater than 1μA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. The voltage should be at least 4V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. A 4 input needs to be operated.
DG309BDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG309BDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG309BDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Data Acquisition Systems
- Transmit
- Public switching systems
- SDH
- Audio and video routing
- DVD-R
- USB 1.1 signal switching circuits
- Battery Powered Instruments