DG309CJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | TIN LEAD |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Nominal Supply Current | 1nA |
| Power Dissipation | 470mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Drain to Source Resistance | 60Ohm |
| RoHS Status | Non-RoHS Compliant |
DG309CJ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. There is an analog multiplexer mounted in position Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. The analog switch ics are built using SPST - NC switching circuits. The internal resistance of this digital multiplexer is 85Ohm. Datasheets for 16 pin functions are available upon request. A voltage higher than 36V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. There should be 13V voltage fed to the electrical part below 13V. If put voltage greater than 10μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 22VFor dual power supplies, a voltage of at least 7V should be attached. The electrical part can be operated at 15V voltage levels. The electrical component supports 4 inputs. There is 60Ohm resistance between the Drain and Source on this part.
DG309CJ Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 60Ohm
DG309CJ Applications
There are a lot of Rochester Electronics, LLC DG309CJ Analog Switches & Multiplexers ICs applications.
- Industrial
- Avionics
- High speed data transmission line cards
- Isolation
- Communication systems
- Medical
- PDH Multiplexers
- FTTH
- CSU
- Imaging
