DG309CJ
| Parameters | |
|---|---|
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG309 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | -10pC |
DG309CJ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. Through Hole is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 16 pins. A SPST - NC switching circuit is used for these analog switches. The multiplexer consists of 4 circuits. Try searching with DG309 to find analog multiplexer variants. Analog switches have 100Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 30V. The analog switch ic is of the Dual supply type and is cost-effective. A low voltage of 5V should be applied to the electronic component. The analogue multiplexer could operate on 1nA current. If you put voltage higher than 100μA on the digital multiplexer, damage may occur. For this switch, a dual supply voltage is feasible, but it must not exceed 20VThe voltage should be at least 5V if you are using dual power supplies. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 18V operating voltages can be used with this electrical part.
DG309CJ Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
DG309CJ Applications
There are a lot of Maxim Integrated DG309CJ Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Data switching
- Precision data acquisition
- Avionics
- USB 1.1 signal switching circuits
- Relay Replacement
- Ultrasound
- Audio and video switching
- FTTH
- Automatic test equipment
