DG309DJ
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG309 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 5V |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | -10pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 200ns |
| Switch-off Time-Max | 150ns |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG309DJ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 16. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. This multiplexer is composed of 4 circuits. DG309 can be used to search for analog multiplexer variants. A 100Ohm internal resistance characterizes this multiplexer. For details about the functions of 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. It is recommended to use 5V as the lowest voltage for the electrical part. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. For dual power supplies, a voltage of at least 5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
DG309DJ Features
1 Channels
Switch Circuit: SPST - NC
DG309DJ Applications
There are a lot of Maxim Integrated DG309DJ Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Audio and video signal routing
- Channelized and Unchannelized DS3 applications
- Optical Applications
- High-Voltage
- RGB switches
- Communications systems
- Cable Modem
- Public switching systems
- Digital access cross connects
