DG309DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG309 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 5V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±5V~20V |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 150ns |
| Charge Injection | -10pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG309DY Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching for the analog switch ic with DG309 if you are looking for variants. This digital multiplexer has 100Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 20V voltage to the switch device. Digital switch that provides Dual power at a cost-effective price. In order for the electronic part to function properly, the lowest voltage should be 5V. This digital switch can be operated with a current of 1nA. Put voltage above 100μA on the multiplexer to cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIn the case of dual power supplies, you should connect at least 5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG309DY Features
4 Channels
Switch Circuit: SPST - NC
1nA Supply Current
DG309DY Applications
There are a lot of Maxim Integrated DG309DY Analog Switches & Multiplexers ICs applications.
- DVD-R
- Frame Relay Equipment
- Sample hold systems
- Video switching
- PDH Multiplexers
- Precision test equipment
- Mechanical reed relay replacement
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Signal routing between systems
- PCMCIA cards
