DG309DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Nominal Supply Current | 1nA |
| Power Dissipation | 600mW |
| Max Supply Current | 10μA |
| Turn On Delay Time | 200 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±4V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1.7 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| RoHS Status | Non-RoHS Compliant |
DG309DY Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. In total, 16 terminations have occurred. An 15V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 16 pins. The analog switch ics are built using SPST - NC switching circuits. As far as internal resistance is concerned, it has 85Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. It may damage the digital multiplexer if the voltage is higher than 10μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages of 15V are compatible with the electrical part. The electrical component supports 4 inputs.
DG309DY Features
Switch Circuit: SPST - NC
DG309DY Applications
There are a lot of Vishay Siliconix DG309DY Analog Switches & Multiplexers ICs applications.
- Microprocessor Controlled Analog Systems
- T1/E1 Terminals
- Precision test equipment
- Multi-Line E1 Interface Cards
- Transmit
- Routers
- Audio and video signal routing
- E1 Network Equipment
- Industrial
- MP3 players
